How to set the Time on your Hot Tub Control Panel – Gecko INK300 control panel

Press and hold the light button for approximately 10 seconds.

The digital clock will now start flashing. Now, press and hold the arrow key on the right hand side of the control panel.

As you hold the key down, the hour unit will decrease until it reaches zero. Release the key and hold it in again to increase the hour unit.

Once the correct hour is set, press the light button. You will now be able to alter the minute units on the clock. The method is the same for altering the minutes as it is for altering the hours. Once the time has been set, press the light button to save.

Once the correct hour is set, press the light button. You will now be able to alter the minute units on the clock. The method is the same for altering the minutes as it is for altering the hours. Once the time has been set, press the light button to save.

How to Set the Filter Cycle on your Spa - Gecko INK300 control panel

Press and hold the light button until the time display starts to flash.

Once the time starts to flash, press the light button twice.

The ‘FS’ display should now show on the screen. This starts for ‘Filter Start’. The filter start time is set using a 24 hour clock, you can change the time using the arrow key and set it to whatever time you choose.

If you press the light button again, you the screen will show ‘FD’ for filter duration. You can change the filter duration using the arrow key. We usually recommend setting the time to around 2 hours, twice a day.

Press the light key again and the ‘FF’ for ‘filter frequency will display. This is how many times you would like the filter to run each day. As we mentioned, we recommend you set the number to 2, so that the filter can run twice a day.

The screen should now display ‘EP’ which stands for economy mode. The ‘0’ next to this indicates that economy mode is off. To turn economy mode on, press the arrow key until a ‘1’ displays on the screen. Please bear in mind that economy mode will reduce the temperature of your hot tub.

How to Connect to Your Hot Tub’s Bluetooth sound system

Some of our hot tubs are equipped with Bluetooth speakers. These are Located either on the cabinet or on the top side of the acrylic. Some hot tubs are also equipped with pop up speakers. All our speakers are controlled in the same way.

To connect to the Bluetooth...

Turn the Bluetooth connection on on your phone or tablet and search for the device.

How to remove an airlock from your spa

This guide will show you how to remove any air that may be trapped in your hot tub’s circulation system.

Air can become trapped because of a low water level, a blocked filter or filling the spa incorrectly.

Trapped air can be identified by a rattling or whirring noise.

The first course of action to take if you notice any unusual sound is to remove the filter from the filter housing.

Once you have removed the filter, make sure you turn the hot tub’s power off from the main power supply and unplug.

The circulation pump can be found behind the cabinet of your hot tub.

Once you have located the pump, the first thing to do is loosen the cuff that joins the pump onto the pipe work. You may notice a hissing or squealing noise as air escapes from the system. Let the water trickle out for about five seconds, and then screw the joint on tightly.

Make sure to do this with both cuffs that join the pump onto the pipe work.

If noise persists after the air has been removed, please contact combined shipping and a member of the team will investigate the issue further.

How to Drain your Hot Tub

This is the drainage valve you will find on the bottom of your hot tub’s ABS base. Depending on your hot tub model, the valve may be located in any of the corners or the side of the hot tub base.

The spout of the valve should be set to the locked position, preventing water from flowing out. To allow water to flow, push the spout inwards and make sure it can rotate. Water should now be able to flow freely from the spout.

Some spouts may be inside the valve, you will need to retrieve it from inside the valve to allow water to flow. To retrieve the spout, insert your thumb inside the valve and twist. You should now be able to pull the spout out.